Showing posts with label Sterling tire. Show all posts
Showing posts with label Sterling tire. Show all posts

Wednesday, November 26, 2014

Blackborow DS: How To Change Gears & More

My new Blackborow DS size Large.
Today I wanted to answer a question I received yesterday concerning how one changes gears on a Blackborow DS. Obviously, there are no shifters and it must be done manually. I will show how it's done in some images and with words. Then I'll have a bit more to say about my impressions concerning the bike.

The Blackborow DS was ridden in the "high" ratio set of gears today, so I will demonstrate here a switch to "low range". It takes all of about three to four minutes to accomplish a gear change. You do not need any special tools and I would recommend a rag to clean your hands since the chain will likely be greasy when you do this, although mine is pretty good looking yet since it is so new!

By the way, you shouldn't, (and cannot), cross chain the bike. I also will add that the rear hub has a full range free hub body, so if you should decide after getting a DS that you have to have gears, all you need are the parts plus a through axle, driveside, derailleur compatible Alternator plate. The cable stops are all there to run the cable to the rear derailleur should you decide to add that dangly bit. Okay, enough about all of that. Now I will get into how to change the gears here.

A closer look at the cogs and drop out. This is the side the axle screws in to. 
Here's the Maxle lever which you flip open like a normal QR, but then you use it like a wing nut and unscrew it.....

....until you can start to pull the axle clear of the wheel/hub. Leave the bike on the ground at this point. 
Then lift the rear of the bike straight up. This allows for some chain slack. See below for further instructions.
  • Once the rear of the bike is up and you have created some chain slack, reach down with your hand and starting with the rear cog, grab the chain at the top of the cog, lift and move it over to the next cog. In my case, the inner one.
  • This next step is crucial to an easy, smooth gear change. Reach down to the bottom run of the chain near the crank set and guide the chain onto the chain ring of choice, (in my case, the inner one), and push the chain "backwards", as if back pedaling, since the crank and cogs will free wheel backward while the wheels remain static. Make sure the pedals are free to rotate! Guide the chain carefully from the bottom up around to the top until it is on the chain ring. Oh.....you're still holding the bike up, by the way. 
  • Once the chain is on the set of gears you want, gently lower the rear of the bike, making sure the rotor passes between the pads in the caliper. Line up the hub and the inner drop out "hoods" and then set the weight of the bike on the hub end caps. Replace the Maxle, screwing it into the drive side drop out snugly, but don't reef on it! Then close the lever. That's it!

The gears swapped and the wheel sitting on the hub end caps before reinstalling the Maxle. 
More Impressions: 

The Blackborow DS was ridden to work in "high" range and that makes a speed sufficient for brisk travel. It can be a chore in fluffy, slushy snow though, and going up longer inclines can get a bit wearisome. I'd say anyone used to a stout gear for mtb should be okay with it. My commute, about 4 miles or so, is mostly uphill and if there is any amount of fresh snow or a stiff wind, I'll probably be dumping it back into the low range. The high range was a chore yesterday, but it should make me stronger if I can get used to it. 

The wheel base feels shorter, but I'll have to confirm that. I feel that it is the reason it is really easy to pop a wheelie or loft the front end of this bike. Stand over is definitely what Salsa says, "the best of any" of their fat bikes. That's by at least an inch over the Beargrease and Mukluk. (Large vs Large sizes)

This is my first time on Clown Shoe rims with any of the bigger tires. I noted that this combination is "flatter" crowned than what I have seen with Surly tires. My titanium Mukluk has a Bud on a Rolling Darryl and is noticeably rounder in profile. This flatter profile manifests itself in a bit of self-steer at lower pressures and at similar pressures to the Bud/RD combo, the Clown Shoe/Lou combo is always a bit more prone to the self-steering feel. I'm okay with that with this bike since I got it for the maximum flotation of its tires and rims. It is also worth noting that the barely 4 inch wide Sterlings (made by Vee Tire) have far worse self-steer feelings at these same pressures than do the Clown Shoe/Lou combo. So, it isn't bad with the Blackborow DS, but it is there.

More on this bike later.....

Blackborow DS: How To Change Gears & More

My new Blackborow DS size Large.
Today I wanted to answer a question I received yesterday concerning how one changes gears on a Blackborow DS. Obviously, there are no shifters and it must be done manually. I will show how it's done in some images and with words. Then I'll have a bit more to say about my impressions concerning the bike.

The Blackborow DS was ridden in the "high" ratio set of gears today, so I will demonstrate here a switch to "low range". It takes all of about three to four minutes to accomplish a gear change. You do not need any special tools and I would recommend a rag to clean your hands since the chain will likely be greasy when you do this, although mine is pretty good looking yet since it is so new!

By the way, you shouldn't, (and cannot), cross chain the bike. I also will add that the rear hub has a full range free hub body, so if you should decide after getting a DS that you have to have gears, all you need are the parts plus a through axle, driveside, derailleur compatible Alternator plate. The cable stops are all there to run the cable to the rear derailleur should you decide to add that dangly bit. Okay, enough about all of that. Now I will get into how to change the gears here.

A closer look at the cogs and drop out. This is the side the axle screws in to. 
Here's the Maxle lever which you flip open like a normal QR, but then you use it like a wing nut and unscrew it.....

....until you can start to pull the axle clear of the wheel/hub. Leave the bike on the ground at this point. 
Then lift the rear of the bike straight up. This allows for some chain slack. See below for further instructions.
  • Once the rear of the bike is up and you have created some chain slack, reach down with your hand and starting with the rear cog, grab the chain at the top of the cog, lift and move it over to the next cog. In my case, the inner one.
  • This next step is crucial to an easy, smooth gear change. Reach down to the bottom run of the chain near the crank set and guide the chain onto the chain ring of choice, (in my case, the inner one), and push the chain "backwards", as if back pedaling, since the crank and cogs will free wheel backward while the wheels remain static. Make sure the pedals are free to rotate! Guide the chain carefully from the bottom up around to the top until it is on the chain ring. Oh.....you're still holding the bike up, by the way. 
  • Once the chain is on the set of gears you want, gently lower the rear of the bike, making sure the rotor passes between the pads in the caliper. Line up the hub and the inner drop out "hoods" and then set the weight of the bike on the hub end caps. Replace the Maxle, screwing it into the drive side drop out snugly, but don't reef on it! Then close the lever. That's it!

The gears swapped and the wheel sitting on the hub end caps before reinstalling the Maxle. 
More Impressions: 

The Blackborow DS was ridden to work in "high" range and that makes a speed sufficient for brisk travel. It can be a chore in fluffy, slushy snow though, and going up longer inclines can get a bit wearisome. I'd say anyone used to a stout gear for mtb should be okay with it. My commute, about 4 miles or so, is mostly uphill and if there is any amount of fresh snow or a stiff wind, I'll probably be dumping it back into the low range. The high range was a chore yesterday, but it should make me stronger if I can get used to it. 

The wheel base feels shorter, but I'll have to confirm that. I feel that it is the reason it is really easy to pop a wheelie or loft the front end of this bike. Stand over is definitely what Salsa says, "the best of any" of their fat bikes. That's by at least an inch over the Beargrease and Mukluk. (Large vs Large sizes)

This is my first time on Clown Shoe rims with any of the bigger tires. I noted that this combination is "flatter" crowned than what I have seen with Surly tires. My titanium Mukluk has a Bud on a Rolling Darryl and is noticeably rounder in profile. This flatter profile manifests itself in a bit of self-steer at lower pressures and at similar pressures to the Bud/RD combo, the Clown Shoe/Lou combo is always a bit more prone to the self-steering feel. I'm okay with that with this bike since I got it for the maximum flotation of its tires and rims. It is also worth noting that the barely 4 inch wide Sterlings (made by Vee Tire) have far worse self-steer feelings at these same pressures than do the Clown Shoe/Lou combo. So, it isn't bad with the Blackborow DS, but it is there.

More on this bike later.....

Tuesday, January 28, 2014

The Snow Dog Lives!

The band is gettin' back together......
With the son's new fat bike build last Fall I had to strip down the old Mukluk and hang it from a peg for a while. But now it is back up and running! Here are the details of the build and my thoughts following after not having ridden this bike for a few months or so.

  • Wheels: I used the idle wheel set from the titanium Mukluk. I put the old Larry 3,8's with Bontrager 29"er tubes in there as well. Basically this is the wheel set from the original titanium Mukluk build. 
  • Bottom Bracket/Crankset: New FSA DH 100mm ISIS bottom bracket with some old take-off Bontrager ISIS cranks. I decided since I did not have the front derailleur for this to go 1X9. I used the purple e13 Guide Ring in 32T size from the original titanium Mukluk build. Pedals are some old pinned flats I had lying about. 
  • Cassette, Rear Derailleur: I had a 11 X 34 cassette and an old SRAM X-9 derailleur from the parts bin. 
  • Saddle/Seat post: Right off the original titanium Muk build as well- FSA SLK post and WTB SST saddle. The post is shy of being long enough, so it will get replaced with something else soon. 
  • Brakes: Magura hydraulics that were the brakes on this bike when I stripped it down. I did have to replace the rear rotor with an Avid and the front stayed with the Ashima that was on there, so the rotors are not the matches for the brakes. At some point I will get those rotors back to the originals. 
  • Controls: I used a 9 speed X-9 shifter, the Magura levers, (obviously), and Ergon grips which are no longer in production, but are like the new enduro grips they have coming soon, only those will be smaller and better!
 Ride Notes: 

In no particular order, these are some thoughts I had while riding the Snow dog yesterday....

  • This geometry is stellar for going through deeper, softer terrain. I was feeling that I didn't have to make much for weight shifts. Although the titanium Mukluk is supposed to be the same,  it doesn't handle in the the same way as this bike. It never has, actually. New Mukluks are not the same either. That's why I'll likely keep this one up and running for a long time. 
  • Surly Tires work far better in deep, drifted snow. The verdict will really be served today, as I am using the Sterlings to ride to work, but the Larrys are noticeably better at "float" than the Vee Rubber tires are. Self steer is unheard of, and with the ridiculously low pressures, the tires don't feel like boat anchors to pedal on harder terrain or pavement. The Sterlings have far better forward bite though, and can be set up tubeless, which makes them really good, but more like "regular mountain bike tires" than "fat bike tires". 
  • I need a longer seat post!
  • 1X set ups are okay, but I really need at least a 2X for serious, longer distance fat biking. That or one of them fancy 42T add on cogs for my cassette! 
So, there it is! Back up and running for awhile. I will definitely be tweaking this out as I go along, but it was sure mighty fun having the Snow Dog back underneath me again on a Winter day's ride! 

The Snow Dog Lives!

The band is gettin' back together......
With the son's new fat bike build last Fall I had to strip down the old Mukluk and hang it from a peg for a while. But now it is back up and running! Here are the details of the build and my thoughts following after not having ridden this bike for a few months or so.

  • Wheels: I used the idle wheel set from the titanium Mukluk. I put the old Larry 3,8's with Bontrager 29"er tubes in there as well. Basically this is the wheel set from the original titanium Mukluk build. 
  • Bottom Bracket/Crankset: New FSA DH 100mm ISIS bottom bracket with some old take-off Bontrager ISIS cranks. I decided since I did not have the front derailleur for this to go 1X9. I used the purple e13 Guide Ring in 32T size from the original titanium Mukluk build. Pedals are some old pinned flats I had lying about. 
  • Cassette, Rear Derailleur: I had a 11 X 34 cassette and an old SRAM X-9 derailleur from the parts bin. 
  • Saddle/Seat post: Right off the original titanium Muk build as well- FSA SLK post and WTB SST saddle. The post is shy of being long enough, so it will get replaced with something else soon. 
  • Brakes: Magura hydraulics that were the brakes on this bike when I stripped it down. I did have to replace the rear rotor with an Avid and the front stayed with the Ashima that was on there, so the rotors are not the matches for the brakes. At some point I will get those rotors back to the originals. 
  • Controls: I used a 9 speed X-9 shifter, the Magura levers, (obviously), and Ergon grips which are no longer in production, but are like the new enduro grips they have coming soon, only those will be smaller and better!
 Ride Notes: 

In no particular order, these are some thoughts I had while riding the Snow dog yesterday....

  • This geometry is stellar for going through deeper, softer terrain. I was feeling that I didn't have to make much for weight shifts. Although the titanium Mukluk is supposed to be the same,  it doesn't handle in the the same way as this bike. It never has, actually. New Mukluks are not the same either. That's why I'll likely keep this one up and running for a long time. 
  • Surly Tires work far better in deep, drifted snow. The verdict will really be served today, as I am using the Sterlings to ride to work, but the Larrys are noticeably better at "float" than the Vee Rubber tires are. Self steer is unheard of, and with the ridiculously low pressures, the tires don't feel like boat anchors to pedal on harder terrain or pavement. The Sterlings have far better forward bite though, and can be set up tubeless, which makes them really good, but more like "regular mountain bike tires" than "fat bike tires". 
  • I need a longer seat post!
  • 1X set ups are okay, but I really need at least a 2X for serious, longer distance fat biking. That or one of them fancy 42T add on cogs for my cassette! 
So, there it is! Back up and running for awhile. I will definitely be tweaking this out as I go along, but it was sure mighty fun having the Snow Dog back underneath me again on a Winter day's ride! 

Wednesday, January 22, 2014

WW4M: The Triple D Set Up

This is an occasional feature here that I dubbed "WW4M" which stands for "What Works For Me". Like the title says, this works for me, but it may not necessarily work for you. Any actions taken up based on information shared here is done of your own free will and any resulting consequences are all yours, baby!

The titanium Mukluk set up and ready to go for Triple D this past weekend.
I thought it might be fun and informative to go over my gear from last weekend's succesful Triple D attempt. So here is a basic list for the bike and what was on it......

  • 2012 Salsa Cycles Titanium Mukluk w/Enabler steel fork
  • Bontrager Race Lite crank- vintage early 00's. Uses a ISIS BB from FSA set up 2X with 22/32 rings. Fixation Mesa MP pedals
  • 10 speed Deore XT DynaSys rear derailleur with clutch. (I ran it in the non-clutch position for the event.)
  • 10 speed SRAM cassette. (The least expensive one with an aluminum carrier for the largest cogs) SRAM 10 speed chain with quick link.
  • 10 speed DynaSys Rapid Fire right shifter
  • SRAM X-9 Left shifter 
  • SRAM X-7 high direct mount front derailleur
  • Avid Elixir 9 brakes 180 fr/r rotors
  • FSA SLX stem and handle bar. Ergon BioKork grips
  • Salsa Cycles Regulator titanium post w/Ergon SM-3 saddle
  • Velocity Dually rims laced to Hope Fatsno hubs. Fatback Sterling tires set up tubeless at 15psi each.
  • Velocity Bottle trap cages on the fork. Customized Salsa purple ano skewers. 
  • Modified SKS Grand MOM fender for the rear
Okay, so that's the basic bike set up. Now for the bags. I used Bike Bag Dude Chaff Bags on the handle bars. These cylindrical bags  can easily hold a large water bottle, but I filled both of mine with some salty, sweet, hot flavored snacks. The Chaff Bag keeps them at hand and I stayed fueled much better with the ability to easily eat on the fly. The other BBD bag on board was the Ultra-Light frame bag. Now I've been over-stuffing this thing for quite awhile with all sorts of items. This time, here's a short list of what was riding along with me.......

First off, the bag is divided, so in the upper part I had the following...

  • Three insulated 20 oz water bottles
  • Extra head gear like a neck buff, hat, etc.
  • Some extra Fizz tabs from Hammer Nutrition.
  • A Trek tail light. 
  • Crank Brothers pump with gauge.
  • An extra pair of wool socks
In the lower part I had the following......
  • A Surly fat bike tube
  • A Bontrager 29"er tube
  • A Blackburn Toolmanator 3
  • A tire lever
  • CO2 Inflators
 Then I also had a Oveja Negra "Gearjammer Seat pack which held a pair of Endura rain trousers and an Endura rain jacket, in case things got wet and sloppy, or if I needed to swap out outer wear for whatever reason.
Velocity Dually wheels, Fatback Sterlings tubeless, and the Contigo stainless flask
One other small item that worked brilliantly was the Contigo
stainless steel travel mug, re-purposed as a water bottle with dead air space insulation. It worked great, but then again, the temperatures never really tested the things. However; I did ride to work this week with hot coffee in one mounted on the fork in -20°F wind chills and the coffee was still hot. For whatever that is worth. I was actually going to put hot chicken soup in there, but I never got around to that. I should also mention that I used a Trelock LS-950 light which worked flawlessly, although I wished for a helmet light in those last 4 miles in the hilly terrain!


 Wearables:

Of course, some of what I wore was a last minute, desperation purchase since I had forgotten most of my base layer stuff back at home. However; some of the choices hinged on the actual weather, so I took a lot of stuff that never got used. Here's a rundown of what I wore broken down by base layer, mid-layer, outer layer categories:

Base Layer: I wore Northface wool tights and long sleeved top. On the feet I wore a pair of calf length Smart Wool socks made for XC skiing. 

Mid-layer: I wore a Twin Six Thermal Hoodie made from Merino wool. 

Outer Layer: On the bottom I wore Bontrager tights of a cool weather weight, I would say. They definitely were lighter than what most folks would use. Up top I wore a soft shell Endura jacket. This jacket has a huge rear pocket that I stuffed food and extra gear into. 

Hands and Feet: It was warmer than other Triple D races have been, so I wore a pair of mid-weight Keen Hiking boots on my feet that I treated pre-event with Brooks Proofide. I never got wet feet. Hands were covered at various times by either a pair of Smart wool liners in Merino wool or a pair of Answer mid-weight gloves. For much of the event I didn't even wear gloves!

Head: I wore a fleece cap of lighter weight I got from CIRREM one year and my Bell Super helmet. For eyewear I wore a pair of Oakley Radar Locks and at night I switched over to a pair of Tifosi clear lensed glasses for a bit. 


Verdict: Everything worked really well. I had no issues with any of my gear or my bike, other than I was set up for different conditions with my wheel/tire choice. I ran what I had. If I had wheels and tires at my disposal to run, I would have opted for Rolling Darryls and a Bud/Lou combo, but I didn't have that luxury. I'm not sure it would have made a whole lot of difference anyway, and the heavier wheels/tires may actually have been a detriment in the end. I'll never know. 

If the temperatures would have dumped at night, I may have gotten into trouble as I didn't have any extra tops and I sweat completely through everything I had on up top. I suppose I could have swapped outer layers, since I had that, but I was bare minimal with clothing, I thought.  The SKS fender actually worked great and came in really handy in a few wet spots. 

I think the Salsa seat post was a boon to comfort, but there is an issue with it I am going to have to work through. (More on that later) I think bar ends would have been wonderful, but I think this bike may see a different handle bar/controls set up soon. 

Anyway, that's a wrap. Please feel free to ask any questions in the comments section!

WW4M: The Triple D Set Up

This is an occasional feature here that I dubbed "WW4M" which stands for "What Works For Me". Like the title says, this works for me, but it may not necessarily work for you. Any actions taken up based on information shared here is done of your own free will and any resulting consequences are all yours, baby!

The titanium Mukluk set up and ready to go for Triple D this past weekend.
I thought it might be fun and informative to go over my gear from last weekend's succesful Triple D attempt. So here is a basic list for the bike and what was on it......

  • 2012 Salsa Cycles Titanium Mukluk w/Enabler steel fork
  • Bontrager Race Lite crank- vintage early 00's. Uses a ISIS BB from FSA set up 2X with 22/32 rings. Fixation Mesa MP pedals
  • 10 speed Deore XT DynaSys rear derailleur with clutch. (I ran it in the non-clutch position for the event.)
  • 10 speed SRAM cassette. (The least expensive one with an aluminum carrier for the largest cogs) SRAM 10 speed chain with quick link.
  • 10 speed DynaSys Rapid Fire right shifter
  • SRAM X-9 Left shifter 
  • SRAM X-7 high direct mount front derailleur
  • Avid Elixir 9 brakes 180 fr/r rotors
  • FSA SLX stem and handle bar. Ergon BioKork grips
  • Salsa Cycles Regulator titanium post w/Ergon SM-3 saddle
  • Velocity Dually rims laced to Hope Fatsno hubs. Fatback Sterling tires set up tubeless at 15psi each.
  • Velocity Bottle trap cages on the fork. Customized Salsa purple ano skewers. 
  • Modified SKS Grand MOM fender for the rear
Okay, so that's the basic bike set up. Now for the bags. I used Bike Bag Dude Chaff Bags on the handle bars. These cylindrical bags  can easily hold a large water bottle, but I filled both of mine with some salty, sweet, hot flavored snacks. The Chaff Bag keeps them at hand and I stayed fueled much better with the ability to easily eat on the fly. The other BBD bag on board was the Ultra-Light frame bag. Now I've been over-stuffing this thing for quite awhile with all sorts of items. This time, here's a short list of what was riding along with me.......

First off, the bag is divided, so in the upper part I had the following...

  • Three insulated 20 oz water bottles
  • Extra head gear like a neck buff, hat, etc.
  • Some extra Fizz tabs from Hammer Nutrition.
  • A Trek tail light. 
  • Crank Brothers pump with gauge.
  • An extra pair of wool socks
In the lower part I had the following......
  • A Surly fat bike tube
  • A Bontrager 29"er tube
  • A Blackburn Toolmanator 3
  • A tire lever
  • CO2 Inflators
 Then I also had a Oveja Negra "Gearjammer Seat pack which held a pair of Endura rain trousers and an Endura rain jacket, in case things got wet and sloppy, or if I needed to swap out outer wear for whatever reason.
Velocity Dually wheels, Fatback Sterlings tubeless, and the Contigo stainless flask
One other small item that worked brilliantly was the Contigo
stainless steel travel mug, re-purposed as a water bottle with dead air space insulation. It worked great, but then again, the temperatures never really tested the things. However; I did ride to work this week with hot coffee in one mounted on the fork in -20°F wind chills and the coffee was still hot. For whatever that is worth. I was actually going to put hot chicken soup in there, but I never got around to that. I should also mention that I used a Trelock LS-950 light which worked flawlessly, although I wished for a helmet light in those last 4 miles in the hilly terrain!


 Wearables:

Of course, some of what I wore was a last minute, desperation purchase since I had forgotten most of my base layer stuff back at home. However; some of the choices hinged on the actual weather, so I took a lot of stuff that never got used. Here's a rundown of what I wore broken down by base layer, mid-layer, outer layer categories:

Base Layer: I wore Northface wool tights and long sleeved top. On the feet I wore a pair of calf length Smart Wool socks made for XC skiing. 

Mid-layer: I wore a Twin Six Thermal Hoodie made from Merino wool. 

Outer Layer: On the bottom I wore Bontrager tights of a cool weather weight, I would say. They definitely were lighter than what most folks would use. Up top I wore a soft shell Endura jacket. This jacket has a huge rear pocket that I stuffed food and extra gear into. 

Hands and Feet: It was warmer than other Triple D races have been, so I wore a pair of mid-weight Keen Hiking boots on my feet that I treated pre-event with Brooks Proofide. I never got wet feet. Hands were covered at various times by either a pair of Smart wool liners in Merino wool or a pair of Answer mid-weight gloves. For much of the event I didn't even wear gloves!

Head: I wore a fleece cap of lighter weight I got from CIRREM one year and my Bell Super helmet. For eyewear I wore a pair of Oakley Radar Locks and at night I switched over to a pair of Tifosi clear lensed glasses for a bit. 


Verdict: Everything worked really well. I had no issues with any of my gear or my bike, other than I was set up for different conditions with my wheel/tire choice. I ran what I had. If I had wheels and tires at my disposal to run, I would have opted for Rolling Darryls and a Bud/Lou combo, but I didn't have that luxury. I'm not sure it would have made a whole lot of difference anyway, and the heavier wheels/tires may actually have been a detriment in the end. I'll never know. 

If the temperatures would have dumped at night, I may have gotten into trouble as I didn't have any extra tops and I sweat completely through everything I had on up top. I suppose I could have swapped outer layers, since I had that, but I was bare minimal with clothing, I thought.  The SKS fender actually worked great and came in really handy in a few wet spots. 

I think the Salsa seat post was a boon to comfort, but there is an issue with it I am going to have to work through. (More on that later) I think bar ends would have been wonderful, but I think this bike may see a different handle bar/controls set up soon. 

Anyway, that's a wrap. Please feel free to ask any questions in the comments section!

Thursday, January 16, 2014

Triple D 2014: Last Big Training Ride

ATV ruts, Leroy & his dog's tracks, and some melt/freeze cycles get you this.
Wednesday, the day off work, and a chance to get in a longer ride to ascertain whether or not I am recovering or getting worse off. First I had some erands to run, then a bit of lunch. When I hit out to ride, it was about 15°F with a light wind.

I headed on down to the Sergeant Road trail to see how badly it had iced over, or not. Much to my relief, the two plus days of warm weather had not ruined the snow here. For sure- it was icier and far, far bumpier. I liked that fact, because I certainly was looking for a test of my new Dually rim set up for Triple D. I wasn't disappointed, despite Leroy and his dog's best efforts to make the surface uneven and rough with their daily passing through here. Leroy is a local to my neighborhood, and he does a cracking job of taking care of his old German Shepard. He also is very "duck footed", and he tears up the trail like no other when it is snowed over! I didn't see Leroy and his dog on this day. I was too early for his circuit.

I decided to check out the Green Belt after a little traverse past a City Parks worker who was laying down rock salt to melt off some icy patches. He was rather taken aback by my bike and I, and did not return my greeting. Hmmm.....maybe he was having a bad day?

The Green Belt was ridiculously fast and packed in.

Well, I climbed the dike and descended it safely down into the wood, and I found a treat. The snow had been tamped down quite smoothly by prior traffic, and frozen like a rock with the recent melt then re-freeze. I was going as fast here in Winter as I do in summer. This was a lot of fun, and I didn't notice I was on fatter wheels at all. The ponderous, slower handling I was used to was lessened, and the bike seemed to spin up off of corners quite nicely, in comparison to how it used to be.

So far into the ride, I also hadn't noticed any odd traits from swapping wheels, only better feelings, like a snappier turning feel, and if anything, a less "planted" feeling when going slower. More like a 26"er hard tail, but without the negatives of the skinnier, smaller diameter wheels. That is not saying "it felt like a 26"er", it just says it moved toward feeling that way more than not, mmm-kay folks. Of course, the loss of weight in the wheels is most likely the reason for all of that. I mean, if you can shave a massive amount of weight off your wheels, it is something any rider would immediately notice, so this is not rocket science stuff here. (Keep in mind, these wheels are just shy of 3lbs lighter than the old set.)

Like riding on firm Styrofoam!
Then I made my way around toward the lake, as I was following someone's orange surveyor flags, and I wanted to see what the route was. Well, it was what I probably would have done anyway- Green Belt to a loop around the lake. The snow was perfect! Really fast here, and the snow was still lily white, packed in, firm, and sounded like crunchy Styrofoam under the tires. Lots of fun!

The Sterlings were getting a ton of traction out here, so this was a good little stretch to push up the speeds a bit. However; I had to throttle it waaaaaay back when I left through the parking lot, as it was a sea of glassy looking ice. I would probably avoid it next time if I see that it is still like this. It was by far the most treacherous ice of the entire ride.

Then came the bike path again to get back home, and to begin with, there was a modicum of traffic that had made somewhat of a rut/impression into the snow. Leroy and his dog do not venture out this far on the trail, otherwise it would have been as before, closer to my home. I got within 50-75 yrads of Ansborough Avenue, and free and clear tracks again, when all signs of any consistent track disappeared. It was essentially snow that hadn't been walked on for a long time, if ever. I could not see evidence of a foot print, at any rate.
Rut-ro! Fat bike, comin through!


 So I kicked the front derailluer down to granny gear, (literally, it had been so long since I had used it, the mech was frozen!), and spun away in a low-ish gear with not much of a problem. The searing, tearing sound of the snow was amazing. It got real loud!

I noticed that I was getting into some deeper stuff, so now I click down a couple more gears, power down, and it keeps on moving! Fun, but a lot of work. I noted that I was spinning pretty fast for my forward speed, and then I noticed the rear tire was actually spinning faster than I was going! Don't stop now!

As I got closer to the Ansborough bike path, I saw a set of tracks made by a walker, but I steered clear and made my own way. Sometimes a single set of post holes will kill your mojo. Not this time! I was going to clean this section! I kept churning, and eventually, I popped off onto the cement path and stopped to catch my breath.

So, the Sterlings still have that tractability, and they "floated" me as well as I have expected so far, with a better spin up due to the lighter weight. In the high output section I had just cleared, I wonder if I would have been able to keep a heavier wheel going like I did. It's hard to say, but I bet that the lighter wheels helped a lot here. The rest of the ride was a piece of cake, and I returned home after two hours of pedaling.

That was a good test, and I am confident in my tubeless set up with the Duallys, as well as being very impressed with how they performed with the Sterlings. This should really help out with saving energy during Triple D, and I really need that this year, as last week's being very sick has been a blow to my fitness, and recovery is not complete yet.

Onward and upward........


Triple D 2014: Last Big Training Ride

ATV ruts, Leroy & his dog's tracks, and some melt/freeze cycles get you this.
Wednesday, the day off work, and a chance to get in a longer ride to ascertain whether or not I am recovering or getting worse off. First I had some erands to run, then a bit of lunch. When I hit out to ride, it was about 15°F with a light wind.

I headed on down to the Sergeant Road trail to see how badly it had iced over, or not. Much to my relief, the two plus days of warm weather had not ruined the snow here. For sure- it was icier and far, far bumpier. I liked that fact, because I certainly was looking for a test of my new Dually rim set up for Triple D. I wasn't disappointed, despite Leroy and his dog's best efforts to make the surface uneven and rough with their daily passing through here. Leroy is a local to my neighborhood, and he does a cracking job of taking care of his old German Shepard. He also is very "duck footed", and he tears up the trail like no other when it is snowed over! I didn't see Leroy and his dog on this day. I was too early for his circuit.

I decided to check out the Green Belt after a little traverse past a City Parks worker who was laying down rock salt to melt off some icy patches. He was rather taken aback by my bike and I, and did not return my greeting. Hmmm.....maybe he was having a bad day?

The Green Belt was ridiculously fast and packed in.

Well, I climbed the dike and descended it safely down into the wood, and I found a treat. The snow had been tamped down quite smoothly by prior traffic, and frozen like a rock with the recent melt then re-freeze. I was going as fast here in Winter as I do in summer. This was a lot of fun, and I didn't notice I was on fatter wheels at all. The ponderous, slower handling I was used to was lessened, and the bike seemed to spin up off of corners quite nicely, in comparison to how it used to be.

So far into the ride, I also hadn't noticed any odd traits from swapping wheels, only better feelings, like a snappier turning feel, and if anything, a less "planted" feeling when going slower. More like a 26"er hard tail, but without the negatives of the skinnier, smaller diameter wheels. That is not saying "it felt like a 26"er", it just says it moved toward feeling that way more than not, mmm-kay folks. Of course, the loss of weight in the wheels is most likely the reason for all of that. I mean, if you can shave a massive amount of weight off your wheels, it is something any rider would immediately notice, so this is not rocket science stuff here. (Keep in mind, these wheels are just shy of 3lbs lighter than the old set.)

Like riding on firm Styrofoam!
Then I made my way around toward the lake, as I was following someone's orange surveyor flags, and I wanted to see what the route was. Well, it was what I probably would have done anyway- Green Belt to a loop around the lake. The snow was perfect! Really fast here, and the snow was still lily white, packed in, firm, and sounded like crunchy Styrofoam under the tires. Lots of fun!

The Sterlings were getting a ton of traction out here, so this was a good little stretch to push up the speeds a bit. However; I had to throttle it waaaaaay back when I left through the parking lot, as it was a sea of glassy looking ice. I would probably avoid it next time if I see that it is still like this. It was by far the most treacherous ice of the entire ride.

Then came the bike path again to get back home, and to begin with, there was a modicum of traffic that had made somewhat of a rut/impression into the snow. Leroy and his dog do not venture out this far on the trail, otherwise it would have been as before, closer to my home. I got within 50-75 yrads of Ansborough Avenue, and free and clear tracks again, when all signs of any consistent track disappeared. It was essentially snow that hadn't been walked on for a long time, if ever. I could not see evidence of a foot print, at any rate.
Rut-ro! Fat bike, comin through!


 So I kicked the front derailluer down to granny gear, (literally, it had been so long since I had used it, the mech was frozen!), and spun away in a low-ish gear with not much of a problem. The searing, tearing sound of the snow was amazing. It got real loud!

I noticed that I was getting into some deeper stuff, so now I click down a couple more gears, power down, and it keeps on moving! Fun, but a lot of work. I noted that I was spinning pretty fast for my forward speed, and then I noticed the rear tire was actually spinning faster than I was going! Don't stop now!

As I got closer to the Ansborough bike path, I saw a set of tracks made by a walker, but I steered clear and made my own way. Sometimes a single set of post holes will kill your mojo. Not this time! I was going to clean this section! I kept churning, and eventually, I popped off onto the cement path and stopped to catch my breath.

So, the Sterlings still have that tractability, and they "floated" me as well as I have expected so far, with a better spin up due to the lighter weight. In the high output section I had just cleared, I wonder if I would have been able to keep a heavier wheel going like I did. It's hard to say, but I bet that the lighter wheels helped a lot here. The rest of the ride was a piece of cake, and I returned home after two hours of pedaling.

That was a good test, and I am confident in my tubeless set up with the Duallys, as well as being very impressed with how they performed with the Sterlings. This should really help out with saving energy during Triple D, and I really need that this year, as last week's being very sick has been a blow to my fitness, and recovery is not complete yet.

Onward and upward........


Friday, January 03, 2014

Friday News And Views

Colder than it looks
Hello from Iowa where it is a balmy.....something or another below zero. I mean really.....when it gets to ten below, anything beyond that is just silly. 

We've likely hit our coldest stretch of Winter a little earlier than maybe we usually do. That's good if true, I mean, let's just get this out of the way right now, eh? Interestingly, we're getting a day of reprieve Saturday when it is supposedly going to soar up into the 20's above. Wow! I think I'll unzip my coat a little!

However; post Saturday we go back into the deeper freeze with some silly forecast temperatures until Tuesday when things bounce back the other way. (Well, at least we are hoping so!) Then it seems that it stays that way for the near term through to Triple D. I sure hope it isn't 15 below the morning of that event!

Of course, it is hard to say what Winter may bring by the time Triple D rolls around, but I will be trying to cope with strategies as the temperature forecasts change on the way toward that event. I will be wearing totally different gear if it is above zero as opposed to below zero. I will be carrying more clothing to swap out if it is colder, and less, or none, if it is warmer, and that depends upon how warm it gets, or it doesn't.

See? It's a game of chess with the conditions. Make the wrong move, and you're toast. Heck, I may be bringing a small trunk load of clothes and gear with me on this venture, who knows?!

Want to start a debate? Choose tires as a subject!
Never discuss politics or tires in mixed company: 

In all of my days of writing on the inner-googles, I've probably never seen more debate sparked by anything more than I have with regard to tires. Tires- be they tubeless, not tubeless, toobed, not toobed, wide, thin, big, small, slick, or treaded, you just don't seem to get people all together on the subject of tires. In fact, it seems that for some folks it is akin to a religious offense if a view other than their own is presented as a valid option.

Of course, I was oft accused of being one of these "29"er zealots" eight years ago or so. Heck, I didn't really care what anyone else rode, as long as they were having fun. I just really saw a good point or two about having bigger diameter wheels on my off road bikes. And I still do, of course, but ya know, the wagon wheels done went mainstream nowadays and having beliefs like mine are seen as being "old school" now! Funny how the world changes, ain't it?

Now I went and stirred up the pot, (shame on me), by posting this link on Gravel Grinder News Facebook page and it struck a minor dissonant chord there. Hmmm..... Yep. Tires. They do seem to get the dander up.

Speaking of tires......OH! Yeah....that's right. Never mind!
Sterling Update:

Well, so far so good on the tubeless set up of the Fatback Sterling tires. I have to admit, I had my doubts about how this would go, but so far, I have been duly impressed by the overall set up of the ginormous fat tires. 

Secondly, the big take away for me is how much nicer the Sterlings are tubeless. I would never revert back to tubes if I have a choice here. These are so much better tubeless, it is almost as if they are different tires altogether from the way they ride tubed.

So, a bit of new info here on my take on these tires, in case anyone out there is following along with my rides on these, or cares to know: The tires have stretched a bit more. Now I am getting a 103mm/4.055" measurement on the casings. Keep in mind I started out at barely 3.8" with tubes and this is all on older Fatback Uma II rims which are 70mm wide. So, I can get along with this. Four inches is bigger than I had, and likely on a Rolling Darryl I might find that the overall width might go to closer to the advertised width. Now I am at peace with that part.

The big thing here is the flattened casing profile coupled with the lack of side knobs for lateral stability. The Sterling has drive and braking traction that literally blows the old Larrys away. I have no issues at all with drive traction or braking traction. However; the Sterlings have the uncanny ability to be driving forward with authority and exhibit little to no lateral stability at all. So, this means that you can literally feel the rear tire digging forward, for example, and that same tire is coming around sideways, or slipping into a rut like there is zero resistance to that. It's odd, but out back I can catch that. Up front, it can take off sideways on you and you just loose all forward momentum. Ruts, or softer sections of snow besides a packed track are treacherous anyway, but I think the Sterlings may actually be worse than a BFL up front in this regard. Maybe. It's close if not worse.

If things are well packed in, no worries at all. Ice? Psssshaw! The Sterlings are good on ice within reason. It's that dang lack of lateral stability. I still look at a Surly Bud and think that is the front tire I should have. Sterlings would be a fine rear tire anywhere, but if you don't have groomed trails, a front Sterling may give you fits like it does for me. Maybe. Or I'm just crazy.....

Okay, that's a wrap. Stay warm and safe, but ride em if ya can!

Friday News And Views

Colder than it looks
Hello from Iowa where it is a balmy.....something or another below zero. I mean really.....when it gets to ten below, anything beyond that is just silly. 

We've likely hit our coldest stretch of Winter a little earlier than maybe we usually do. That's good if true, I mean, let's just get this out of the way right now, eh? Interestingly, we're getting a day of reprieve Saturday when it is supposedly going to soar up into the 20's above. Wow! I think I'll unzip my coat a little!

However; post Saturday we go back into the deeper freeze with some silly forecast temperatures until Tuesday when things bounce back the other way. (Well, at least we are hoping so!) Then it seems that it stays that way for the near term through to Triple D. I sure hope it isn't 15 below the morning of that event!

Of course, it is hard to say what Winter may bring by the time Triple D rolls around, but I will be trying to cope with strategies as the temperature forecasts change on the way toward that event. I will be wearing totally different gear if it is above zero as opposed to below zero. I will be carrying more clothing to swap out if it is colder, and less, or none, if it is warmer, and that depends upon how warm it gets, or it doesn't.

See? It's a game of chess with the conditions. Make the wrong move, and you're toast. Heck, I may be bringing a small trunk load of clothes and gear with me on this venture, who knows?!

Want to start a debate? Choose tires as a subject!
Never discuss politics or tires in mixed company: 

In all of my days of writing on the inner-googles, I've probably never seen more debate sparked by anything more than I have with regard to tires. Tires- be they tubeless, not tubeless, toobed, not toobed, wide, thin, big, small, slick, or treaded, you just don't seem to get people all together on the subject of tires. In fact, it seems that for some folks it is akin to a religious offense if a view other than their own is presented as a valid option.

Of course, I was oft accused of being one of these "29"er zealots" eight years ago or so. Heck, I didn't really care what anyone else rode, as long as they were having fun. I just really saw a good point or two about having bigger diameter wheels on my off road bikes. And I still do, of course, but ya know, the wagon wheels done went mainstream nowadays and having beliefs like mine are seen as being "old school" now! Funny how the world changes, ain't it?

Now I went and stirred up the pot, (shame on me), by posting this link on Gravel Grinder News Facebook page and it struck a minor dissonant chord there. Hmmm..... Yep. Tires. They do seem to get the dander up.

Speaking of tires......OH! Yeah....that's right. Never mind!
Sterling Update:

Well, so far so good on the tubeless set up of the Fatback Sterling tires. I have to admit, I had my doubts about how this would go, but so far, I have been duly impressed by the overall set up of the ginormous fat tires. 

Secondly, the big take away for me is how much nicer the Sterlings are tubeless. I would never revert back to tubes if I have a choice here. These are so much better tubeless, it is almost as if they are different tires altogether from the way they ride tubed.

So, a bit of new info here on my take on these tires, in case anyone out there is following along with my rides on these, or cares to know: The tires have stretched a bit more. Now I am getting a 103mm/4.055" measurement on the casings. Keep in mind I started out at barely 3.8" with tubes and this is all on older Fatback Uma II rims which are 70mm wide. So, I can get along with this. Four inches is bigger than I had, and likely on a Rolling Darryl I might find that the overall width might go to closer to the advertised width. Now I am at peace with that part.

The big thing here is the flattened casing profile coupled with the lack of side knobs for lateral stability. The Sterling has drive and braking traction that literally blows the old Larrys away. I have no issues at all with drive traction or braking traction. However; the Sterlings have the uncanny ability to be driving forward with authority and exhibit little to no lateral stability at all. So, this means that you can literally feel the rear tire digging forward, for example, and that same tire is coming around sideways, or slipping into a rut like there is zero resistance to that. It's odd, but out back I can catch that. Up front, it can take off sideways on you and you just loose all forward momentum. Ruts, or softer sections of snow besides a packed track are treacherous anyway, but I think the Sterlings may actually be worse than a BFL up front in this regard. Maybe. It's close if not worse.

If things are well packed in, no worries at all. Ice? Psssshaw! The Sterlings are good on ice within reason. It's that dang lack of lateral stability. I still look at a Surly Bud and think that is the front tire I should have. Sterlings would be a fine rear tire anywhere, but if you don't have groomed trails, a front Sterling may give you fits like it does for me. Maybe. Or I'm just crazy.....

Okay, that's a wrap. Stay warm and safe, but ride em if ya can!

Thursday, December 19, 2013

Triple D 2014: Unusual Warmth

Low Sun Angle
I had to set up By-Tor The Titanium Mukluk with its new drive train in the morning yesterday and do a bit of cleaning and fine tuning. I also had to track down my Loc-Tite for the chain ring bolts. Never put together chain ring bolts without Loc-Tite!

I found the thread locking fluid eventually and the job went smoothly afterward. I ate a quick lunch then got things together for a trip to the shop to drop off my Fox fork for an overhaul. Then I took "the long way home."

I decided to hit up Hartman Reserve first. Bikes are only allowed on the "lower" part, which is a sliver of land in the flood plain, mostly on the North side of old "Shirey Way", which was reputed to be the area where the "devil worshipers" congregated back in the 80's. Pfft! I never really put much credence in that story, but there it is.

Whatever the case was, on this gloriously sunny and warm, (for mid-December), day there were no evil spirits detected in the woods. Just nice, packed in single track, which my now tubeless Sterling tires were eating up like crazy. I will likely have more to say on the tubeless Sterlings in a separate post, but for now I will just say that they are a 180 degrees different feeling and performing tire tubeless over when you are running tubes in them. Simply stated, don't run the Fatback Sterling tires with a tube unless it is an emergency bail-out method to get you back home.

George Wyth State Park single track

Anyway, back to the weather! It was really quite warm out. I noted a temperature of over 40°F at one point, so the snow was softer where there were less trees. Fortunately, the Sun is at its lowest ebb in the sky these days. Had we gotten a day like this a month ago- or in February, the snow would have quickly melted into mush with the more direct rays from the Sun. That said, the trails were surprisingly firm. After yesterday we are to go back to under freezing temperatures for awhile, so whatever we have left for snow should be sticking around for a bit.

I passed by an almost totally frozen Alice Wyth Lake on my ride.
Trail conditions were holding up rather well throughout my ride though, so I kept motoring onward and decided to swing through George Wyth as well. The day was just too awesome to go straight home, and I needed to get a longer ride in.

A few places got kind of sketchy, like where the dang snow machine went down the bike path in George Wyth, as a for instance. The track of the snowmobile made tire footing treacherous in spots. I bailed off the main bike path to get away from that and found the newly flagged trail out on the Eastern end of the park.

It was bumpier, looser, and had log "teepees" to cross over, so it was slower going, but I only dabbed once, so I was pretty happy with that! Then I was looking to exit the park, and thankfully the trail dumped me out right at the ramp up onto the Cedar River bridge, which I needed to cross. One thing about bridges with attached bike paths and Winter: You always have the scrapings from the snowplows piled up on the path. It can be a big problem to ride on/through. Most often, the chemical stuff they use to de-ice and keep the roadway clear can turn the snow on the bike/ped way into something the consistency of mashed potatoes. The snow here was fortunately still rideable though, so I was able to ride the bridge, albeit slowly. The screaming traffic was awful, by the way. I hate riding beside busy roads!

More single track in George Wyth State Park


Then I finally crossed the bridge and started to take note of some excessive drag on the drive train. I decided to stop and take a good look at the bike to see just what it was that was keeping me from feeling "free". Maybe my new drive train was having an issue?

A wee bit of snow build up!
I was a bit surprised by the amount of snow that had attached itself to my bike, especially around the crank and front derailleur area. The drag was snow rubbing the rear tire. I cleared everything off and felt the immediate "free-ness" of everything- the pedaling, coasting, and drive line. It is always amazing to me how "in tune" to that I can be.

So, anyway, the riding continued and the Sun was dipping lower on the horizon. I was thinking I may need to turn on the lights, but for the time being, I just pushed on the rear tail light. I could see just fine.

I wound my way down through alleys and side streets to keep things interesting and to stay on snow as much as possible. Then back on my commute route and onward to the house. I was tired and hungry. I think I got in a good 2 plus hour ride after stopping at the shop, and probably a half an hour before that getting down there. A good kick off to the steady build up to Triple D.

I attended to the chain after getting the bike down into my "Lab". The rust monsters are tough to keep at bay when you have so much wet snow and chemical road treatment to ride through. The new chain ring size is perfect for snow riding, and even going up the steeps, I stayed in the outer ring. Never used the granny today. That's good!

More soon.....

Triple D 2014: Unusual Warmth

Low Sun Angle
I had to set up By-Tor The Titanium Mukluk with its new drive train in the morning yesterday and do a bit of cleaning and fine tuning. I also had to track down my Loc-Tite for the chain ring bolts. Never put together chain ring bolts without Loc-Tite!

I found the thread locking fluid eventually and the job went smoothly afterward. I ate a quick lunch then got things together for a trip to the shop to drop off my Fox fork for an overhaul. Then I took "the long way home."

I decided to hit up Hartman Reserve first. Bikes are only allowed on the "lower" part, which is a sliver of land in the flood plain, mostly on the North side of old "Shirey Way", which was reputed to be the area where the "devil worshipers" congregated back in the 80's. Pfft! I never really put much credence in that story, but there it is.

Whatever the case was, on this gloriously sunny and warm, (for mid-December), day there were no evil spirits detected in the woods. Just nice, packed in single track, which my now tubeless Sterling tires were eating up like crazy. I will likely have more to say on the tubeless Sterlings in a separate post, but for now I will just say that they are a 180 degrees different feeling and performing tire tubeless over when you are running tubes in them. Simply stated, don't run the Fatback Sterling tires with a tube unless it is an emergency bail-out method to get you back home.

George Wyth State Park single track

Anyway, back to the weather! It was really quite warm out. I noted a temperature of over 40°F at one point, so the snow was softer where there were less trees. Fortunately, the Sun is at its lowest ebb in the sky these days. Had we gotten a day like this a month ago- or in February, the snow would have quickly melted into mush with the more direct rays from the Sun. That said, the trails were surprisingly firm. After yesterday we are to go back to under freezing temperatures for awhile, so whatever we have left for snow should be sticking around for a bit.

I passed by an almost totally frozen Alice Wyth Lake on my ride.
Trail conditions were holding up rather well throughout my ride though, so I kept motoring onward and decided to swing through George Wyth as well. The day was just too awesome to go straight home, and I needed to get a longer ride in.

A few places got kind of sketchy, like where the dang snow machine went down the bike path in George Wyth, as a for instance. The track of the snowmobile made tire footing treacherous in spots. I bailed off the main bike path to get away from that and found the newly flagged trail out on the Eastern end of the park.

It was bumpier, looser, and had log "teepees" to cross over, so it was slower going, but I only dabbed once, so I was pretty happy with that! Then I was looking to exit the park, and thankfully the trail dumped me out right at the ramp up onto the Cedar River bridge, which I needed to cross. One thing about bridges with attached bike paths and Winter: You always have the scrapings from the snowplows piled up on the path. It can be a big problem to ride on/through. Most often, the chemical stuff they use to de-ice and keep the roadway clear can turn the snow on the bike/ped way into something the consistency of mashed potatoes. The snow here was fortunately still rideable though, so I was able to ride the bridge, albeit slowly. The screaming traffic was awful, by the way. I hate riding beside busy roads!

More single track in George Wyth State Park


Then I finally crossed the bridge and started to take note of some excessive drag on the drive train. I decided to stop and take a good look at the bike to see just what it was that was keeping me from feeling "free". Maybe my new drive train was having an issue?

A wee bit of snow build up!
I was a bit surprised by the amount of snow that had attached itself to my bike, especially around the crank and front derailleur area. The drag was snow rubbing the rear tire. I cleared everything off and felt the immediate "free-ness" of everything- the pedaling, coasting, and drive line. It is always amazing to me how "in tune" to that I can be.

So, anyway, the riding continued and the Sun was dipping lower on the horizon. I was thinking I may need to turn on the lights, but for the time being, I just pushed on the rear tail light. I could see just fine.

I wound my way down through alleys and side streets to keep things interesting and to stay on snow as much as possible. Then back on my commute route and onward to the house. I was tired and hungry. I think I got in a good 2 plus hour ride after stopping at the shop, and probably a half an hour before that getting down there. A good kick off to the steady build up to Triple D.

I attended to the chain after getting the bike down into my "Lab". The rust monsters are tough to keep at bay when you have so much wet snow and chemical road treatment to ride through. The new chain ring size is perfect for snow riding, and even going up the steeps, I stayed in the outer ring. Never used the granny today. That's good!

More soon.....