Tuesday, October 11, 2016

SRAM NX-1: Impressions

Post Fat Bike Century condition.
NOTE: Large doses of "my opinion" will be handed out in gloppy dollops today. You've been forewarned.....

As many of you know, I have installed the SRAM NX-1 drive train and shifter on my Ti Mukluk. Recently it was flogged on my 100 mile Fat Bike Century ride on gravel roads. This is not a "final verdict" on these parts as I still want to see how the group fares through a Winter's worth of use, but this is a first impression of the group and how it performs for me.

I did do a few shorter rides to break in and fine tune the system before I did my century ride. It didn't take much, since there is only one derailleur, to get tuned into primo performance status. There is a barrel adjuster located at the exit point of the cable from the shifter pod, so adjusting this derailleur on the fly is possible as well, should you need to do that.

The conditions on the ride varied from wet, gritty gravel to dry and pretty dusty. So this was a good test of the system in those specific adverse conditions. There was a tiny bit of rough single track at the very end of the ride so I did get a taste of how stable the system is as well, but otherwise it was all gravel roads with a tiny bit of pavement thrown in.

The heart of the system is undoubtedly the rear derailleur and cassette.
Shifting Performance: I used a non-SRAM chain on this build because I do not trust the longevity of a SRAM 10 or 11 speed chain versus the competition. That said, I saw no compromise in shifting performance versus 1 x 11 systems using SRAM chains I have worked on at the shop. Other than this, the system was all SRAM with the Surly, SRAM approved X-Sync stainless steel chain ring. I've used a higher end SRAM 1X11 system before and this NX stuff is not as fast, nor as crisp shifting in the field as the upper end 1X11 SRAM components. That said, it isn't bad. Just not super snappy or fast. It gets the shifts though, and so if you are not racing, this is still a worthy system. Oh......and far less expensive. 

Under pressure the NX-1 still shifts but the slower nature of the system is amplified over the higher end stuff which still will snap off the shift with a high pitched zing! sound from the chain. This NX stuff doesn't do that, and it is obvious that the shift is a bit laborious. I believe it is because the NX derailleur is not as stiff as the higher end XX-1 and the like. The shifter is really smooth, by the way. The trigger action is easy to initiate and is typical SRAM in an ergonomic sense. Whether that is good or bad is a personal preference issue.

The X-Sync style, SRAM approved 28T Surly ring
Drive Train Stability: While this doesn't cover uses such as rough, rocky single track, or big jumps and moves, I can say that the drive train seems quite stable. As stated, I did have some bumpy single track near the end of my ride and there was nothing negative to report concerning the drive train. So for now, all I can say is that it doesn't seem as though chain drops will be an issue.

I will say that the chain line seems biased toward the higher/smaller cog side of the cassette more. Getting up into the lower gears puts the chain at more of a severe angle, and the lowest two cogs show significantly slower shifting as a result. I blame this on the OD crank set and its offset chain ring mounting scheme in combination with the longer bottom bracket of the Mukluk. Surly says the inner ring mounting position of the OD crank is supposed to be where the middle ring would be on a triple, but it clearly is not lined up with the middle of the NX-1 cassette.

Gearing range for a gravel century on our course called for the fastest cogs to be employed vs the big, low gears.
Gearing Range: Everyone is going to have different needs concerning the gearing range of a 1X11 set up, so this is strictly my opinion based upon my experience and needs. That said, there may be some kernels of knowledge here that you could use.

Clearly, I think it can be agreed that I am not going to be doing big gravel miles a lot with this bike. Maybe I won't ever again, since that is not what I have this bike for. The point is, I could do a gravel century with this gearing set up, and I did. Yes- I was in the smallest four or five cogs almost all day. I did reach into some of those big daddy cogs on the cassette when we traversed the Iowa River Valley, but that was it for low gearing needs.

Now this brings up a simple point. Say that I had the "proper" SRAM NX crank or lets say I had an X-1 type with the removable spider. I could swap rings for a ride like the Fat Bike Century or for an appropriate low cog for a trail breaking fat bike ride. That would "only" require some mechanical work when I wanted to switch up. But......

Again, taking a look at this from a different perspective, let's say that the 1X system existed first. There were no front derailleurs ever before this. Then some whiz-bang company comes up with this idea to mount two rings on a crank set and a chain moving mechanism so you could have a choice. Yeah! Now I don't have to chose a ring before a ride, or be caught out on a ride where I wished I had a bigger or smaller cog for a certain section. Now, wouldn't that be an advantage? 

 So, 1X may be the latest fashion darling of the media and SRAM in particular, but that front derailleur idea is far from dead folks. Furthermore, it is, hands down, a better idea for many. Had I been running the former 2X10 set up I had before, in proper tuned up shape, it would have made for a smarter choice for the Fat Bike Century.

Conclusions: The NX-1 is simpler than a triple to figure out and likely lighter than many double ring set ups. It shifts reasonably well, but it is nothing like the upper end SRAM offerings in 1X11 or 1X12 when it comes to precision and speed. I don't know about longevity yet, but these cogs are stamped steel and the main drive ring is stainless steel, so I am hoping for a Winter's worth of use out of it at the least.

When it comes to details the NX-1 is perhaps a bit suspect. The chain line is going to be compromised more at the extremes due to the larger rear cogs and that even if you get the drive ring in line with the cassette's center cog. The drive ring is going to be a compromise in terms of range and where you end up on the cassette. With a double or triple you can use the Keith Bontrager Rules for shifting and eek out the best possible combination for efficiency and shifting performance. However; that means the rider would have to actually think and use the equipment with skill.

Maybe that's asking too much in these days of ADD folks and innergoogles gaming. Anyway.......

I think NX-1 is the more reasonable choice for 1X11 since you do not have to get a different cassette driver than you already may have, nor is it prohibitively expensive to buy and maintain. Plus, with Shimano doing 1X11 cassettes with wider gearing ranges, the possibility exists to get into a better quality cassette and likely better shifting performance. Basically, there is an upgrade path that doesn't require a new rear free hub and/or a rear wheel. Obviously, a new rear derailleur upgrade path can be had as well. So, for starting out in the 1X11 world, I think NX-1 is really a great option. Just know that if you get into higher end componentry, you will probably not want to return to NX-1 again.

I'll have a long term update on these parts most likely at the end of this coming Winter.

Note- I bought the NX-1 cassette, shifter, and rear derailleur with my own damn money, and that goes for the Surly drive ring and the chain as well. I was not paid nor bribed for this post. So there.......

Monday, October 10, 2016

Weekend Report: A Short Vacation

I know that the following may come as a surprise to some folks out there, but not everything I do revolves around cycling. Yeah......shocking, right? I know that I have contributed to that perception by keeping a pretty straight party line here on the blog, but it just ain't so, in reality. So, here is a bit of a diversion for your Monday reading and pixel peeping pleasure.

The family enjoying roaming the Rollins Mansion grounds
I worked with a fellow named Brian at the shop for a time. Sharper readers of this blog might remember that it was he that passed down the 1X1 frame to me. Anyway, he got married to a long time friend of mine's daughter, whom I've known since she was born. The wedding gig was at a place called the Rollins Mansion in Des Moines and it was a pretty cool venue. Only one issue with attending that service was that we missed it.

Yep. I completely blew the time of the service. It happened at 4:00pm and we didn't get there until just past 5:00pm. Oh well........ If you knew anything about my history concerning weddings, funerals, graduations and the like, you wouldn't be surprised. I have had a knack for getting times, places, and other things wrong. Well, this time it wasn't a total miscue. There was to be a dinner and after party held there, so we had that to look forward to. When we arrived, we snuck in the back way, (yes, the entire family), and mingled about the various folk there as if we had been there the entire time. Somewhat saving face and all, I guess.......

Anyway, the wedding party was getting photographed and someone wandering about informed us that we were encouraged to explore the mansion and grounds in the meantime. so, we did just that. Here are some random shots from the place.

Wedding party photo time
My daughter was enamored of the place.
I always feel like someone is watching me.....
Railing detail.
The two shall become as one.....
So, another thing y'all know about me is that I like flowers. Well, of course, there were flowers at this wedding. But since it was outside, I saw a couple of live flowers that also caught my attention.

Then there are people at weddings. Since I was real familiar with both sides of this deal, I knew a lot of people there. In fact, I saw some folks there I have not seen in a long, long time. This made for a lot of conversations and a very, very late night. Good thing I do Trans Iowa sleep deprivations every year, because I was up until 4:00am in the morning! All totally worth it though.

Former co-worker Jonathan (L) and Mike, a customer of the shop.
Wedding dance revelry.
Probably my favorite image of the weekend- Mrs. Guitar Ted lulling a young reveler to sleep.
There was one thing that was directly related to bicycling that came out of this trip. That was an offer to me by a reader of this blog who was willing to part ways with a tandem to help me fulfill my dream of having a tandem to get the family out together on bicycle rides. "BB" lived just 20 minutes away from the motel where we were staying so I made Saturday the rendezvous time to meet him and pick the rig up.

My son with the new to us tandem
 So, we picked up this Raleigh "Coupe" tandem and took it home. (Thanks BB!) It's already been test ridden by my son and I. so I am sure it will work out just fine for what I wanted it for. Hopefully it will work out that my daughter will finally be able to join the rest of us on family cycling outings. With a few tweaks, I hope to try that out soon.

The entire weekend was something of a vacation for us all. Especially for me. I "unplugged" from just about everything. I resisted checking e-mails and Facebook. (I did a few times) I focused on the people I was with, as much as I could. As I said, many of the people I chatted with I haven't seen in ten years or more. It was good to reconnect. Really good. It was also good to take a break from all the cycling-centric stuff I do. No testing, reviewing, writing, or training. The only time I was on a bicycle all weekend was for the two lap test ride of the tandem around the motel we stayed at with my son.

I even took a vacation from everything Trans Iowa. Maybe that concerned a few of you that sent in post cards and didn't see your name come up on the pages on the site. Well, I have done one update last evening and will do another today to get myself caught back up. If you haven't seen your name, now you know why.

So, that was a great weekend and I am tired and relaxed and ready to go back to the routine with a fresher outlook. It was a good time for the family, and we got a new tool that will hopefully become a thing that will allow us to do an activity I love together. That would be great if it works out that way. We will see. My son thinks he wants to be "Captain" with my daughter on the back. I'm not sure that would work out so well, but you never know.

Weekend Report: A Short Vacation

I know that the following may come as a surprise to some folks out there, but not everything I do revolves around cycling. Yeah......shocking, right? I know that I have contributed to that perception by keeping a pretty straight party line here on the blog, but it just ain't so, in reality. So, here is a bit of a diversion for your Monday reading and pixel peeping pleasure.

The family enjoying roaming the Rollins Mansion grounds
I worked with a fellow named Brian at the shop for a time. Sharper readers of this blog might remember that it was he that passed down the 1X1 frame to me. Anyway, he got married to a long time friend of mine's daughter, whom I've known since she was born. The wedding gig was at a place called the Rollins Mansion in Des Moines and it was a pretty cool venue. Only one issue with attending that service was that we missed it.

Yep. I completely blew the time of the service. It happened at 4:00pm and we didn't get there until just past 5:00pm. Oh well........ If you knew anything about my history concerning weddings, funerals, graduations and the like, you wouldn't be surprised. I have had a knack for getting times, places, and other things wrong. Well, this time it wasn't a total miscue. There was to be a dinner and after party held there, so we had that to look forward to. When we arrived, we snuck in the back way, (yes, the entire family), and mingled about the various folk there as if we had been there the entire time. Somewhat saving face and all, I guess.......

Anyway, the wedding party was getting photographed and someone wandering about informed us that we were encouraged to explore the mansion and grounds in the meantime. so, we did just that. Here are some random shots from the place.

Wedding party photo time
My daughter was enamored of the place.
I always feel like someone is watching me.....
Railing detail.
The two shall become as one.....
So, another thing y'all know about me is that I like flowers. Well, of course, there were flowers at this wedding. But since it was outside, I saw a couple of live flowers that also caught my attention.

Then there are people at weddings. Since I was real familiar with both sides of this deal, I knew a lot of people there. In fact, I saw some folks there I have not seen in a long, long time. This made for a lot of conversations and a very, very late night. Good thing I do Trans Iowa sleep deprivations every year, because I was up until 4:00am in the morning! All totally worth it though.

Former co-worker Jonathan (L) and Mike, a customer of the shop.
Wedding dance revelry.
Probably my favorite image of the weekend- Mrs. Guitar Ted lulling a young reveler to sleep.
There was one thing that was directly related to bicycling that came out of this trip. That was an offer to me by a reader of this blog who was willing to part ways with a tandem to help me fulfill my dream of having a tandem to get the family out together on bicycle rides. "BB" lived just 20 minutes away from the motel where we were staying so I made Saturday the rendezvous time to meet him and pick the rig up.

My son with the new to us tandem
 So, we picked up this Raleigh "Coupe" tandem and took it home. (Thanks BB!) It's already been test ridden by my son and I. so I am sure it will work out just fine for what I wanted it for. Hopefully it will work out that my daughter will finally be able to join the rest of us on family cycling outings. With a few tweaks, I hope to try that out soon.

The entire weekend was something of a vacation for us all. Especially for me. I "unplugged" from just about everything. I resisted checking e-mails and Facebook. (I did a few times) I focused on the people I was with, as much as I could. As I said, many of the people I chatted with I haven't seen in ten years or more. It was good to reconnect. Really good. It was also good to take a break from all the cycling-centric stuff I do. No testing, reviewing, writing, or training. The only time I was on a bicycle all weekend was for the two lap test ride of the tandem around the motel we stayed at with my son.

I even took a vacation from everything Trans Iowa. Maybe that concerned a few of you that sent in post cards and didn't see your name come up on the pages on the site. Well, I have done one update last evening and will do another today to get myself caught back up. If you haven't seen your name, now you know why.

So, that was a great weekend and I am tired and relaxed and ready to go back to the routine with a fresher outlook. It was a good time for the family, and we got a new tool that will hopefully become a thing that will allow us to do an activity I love together. That would be great if it works out that way. We will see. My son thinks he wants to be "Captain" with my daughter on the back. I'm not sure that would work out so well, but you never know.

Friday, October 07, 2016

Friday News And Views

Trans Iowa v13 Registration Update:

 A couple of things to note. One- Plus Six and Active Finishers registration closes up shop tomorrow. So, there will be two mail deliveries to go until that window shuts up. So far there are 12 registered out of a possible 25. Keep in mind that if I don't get 25 folks I will throw the extra slots into the Veteran's Lottery batch which will be a minimum of 55 roster slots.

Two- The Veteran's window to send in cards ends a week from tomorrow. There are several on the list so far, and I expect many more are on their way. However; should there not be over 55 cards sent in, the list will all automatically transfer in on the roster without a drawing, since it wouldn't be necessary. We'll see......

A final note- Rookie Registration has not opened up yet, and won't until the17th. I got one card already and it won't transfer in because of the early arrival. Just a note to ya'all there to make sure you've read the instructions which are linked from the Trans Iowa site.

Maxxis Ravager
Maxxis Introduces A New Aggressive 40mm Tire:

One of the several things "gravel" to come out of Interbike was a tire that is kind of a curious beast. It has an aggressive tread, is tubeless ready, and is 40mm wide. 

Okay, so let's take a look at how this "all-road", adventure bike thing is playing out here for a minute. It would seem that the marketing machine is dictating to us now that an "adventure bike" is a road bike, with big saddle to bar drop difference, a stiff carbon fork, and a big, almost racing bike sized chain ring mated to mountain bike sized tires, or tires that mimic mtb designs.

I disagree with that notion, (and make no mistake, it is where this is all going in terms of design and the narrative the companies are pushing),  but let's just focus on this tire for now. The tire is cool and all, but just think about history for a minute here.

29"er tires were not very numerous ten years ago and of those offerings, 2.1- 2.2"ers were the norm. Racers using 29"er tires were often seen going with 1.8"ers. Guys that were pushing into the 26"er only realm of XC like Jeremy Horgan-Kobelski of the Gary Fisher/Subaru XC racing squad were doing this back then. Why? Because those tires were seen as capable, (barely), and light enough to actually use in that discipline.

But what has this got to do with this Maxxis tire? Consider that 1.8" is equal to 45.7mm, and you can see where I am going here. These 40mm-45mm tires are verging on 29"er territory, and when you design such an aggressive tire, maybe you are looking at a "mtb-lite tire", and not an "all-road" tire, so much. Call this thing a "monster-cross"tire then. Maybe that is what it is. Well, at any rate, the Ravager seems to fall into the end of the spectrum that is more dirt/single track and less "road". I just thought it was an interesting tire from that standpoint.

The whole adventure bike thing, as described by the industry now, is another post for another day. Short version: They are missing the boat big time as far as bringing back riders and bringing in new ones because of how they are portraying these niche bikes now.

One of the several connections I have with Brian and Alexa
Special Occasion:

Today is a special day for a couple that have special connections with myself. Yes......a bicycle is part of the story, so hold on here.

I normally don't get off topic here too far, but today is a special occasion since a former co-worker of mine is marrying a women I've known since she was born. Literally since she was born. I used to be very close to her family, and since I know both of the folks in this marriage, and one of them bequeathed the Surly 1X1 to me , I wanted to give a G-Ted Productions "Congratulations" to the couple.

So, I am attending the nuptials and will be off gallivanting around Central Iowa all weekend long. I won't be getting any bicycling done, but that's excusable for this deal, in my opinion. I wouldn't miss this and since it is happening so close, I don't have to. I am not sure I'll have much else going on except maybe keeping tabs on cards coming in for Trans Iowa, so don't look for any adventurous posts come Monday!

Okay, that's a wrap. Forget about football and get outside and ride, y'all!!

 

Friday News And Views

Trans Iowa v13 Registration Update:

 A couple of things to note. One- Plus Six and Active Finishers registration closes up shop tomorrow. So, there will be two mail deliveries to go until that window shuts up. So far there are 12 registered out of a possible 25. Keep in mind that if I don't get 25 folks I will throw the extra slots into the Veteran's Lottery batch which will be a minimum of 55 roster slots.

Two- The Veteran's window to send in cards ends a week from tomorrow. There are several on the list so far, and I expect many more are on their way. However; should there not be over 55 cards sent in, the list will all automatically transfer in on the roster without a drawing, since it wouldn't be necessary. We'll see......

A final note- Rookie Registration has not opened up yet, and won't until the17th. I got one card already and it won't transfer in because of the early arrival. Just a note to ya'all there to make sure you've read the instructions which are linked from the Trans Iowa site.

Maxxis Ravager
Maxxis Introduces A New Aggressive 40mm Tire:

One of the several things "gravel" to come out of Interbike was a tire that is kind of a curious beast. It has an aggressive tread, is tubeless ready, and is 40mm wide. 

Okay, so let's take a look at how this "all-road", adventure bike thing is playing out here for a minute. It would seem that the marketing machine is dictating to us now that an "adventure bike" is a road bike, with big saddle to bar drop difference, a stiff carbon fork, and a big, almost racing bike sized chain ring mated to mountain bike sized tires, or tires that mimic mtb designs.

I disagree with that notion, (and make no mistake, it is where this is all going in terms of design and the narrative the companies are pushing),  but let's just focus on this tire for now. The tire is cool and all, but just think about history for a minute here.

29"er tires were not very numerous ten years ago and of those offerings, 2.1- 2.2"ers were the norm. Racers using 29"er tires were often seen going with 1.8"ers. Guys that were pushing into the 26"er only realm of XC like Jeremy Horgan-Kobelski of the Gary Fisher/Subaru XC racing squad were doing this back then. Why? Because those tires were seen as capable, (barely), and light enough to actually use in that discipline.

But what has this got to do with this Maxxis tire? Consider that 1.8" is equal to 45.7mm, and you can see where I am going here. These 40mm-45mm tires are verging on 29"er territory, and when you design such an aggressive tire, maybe you are looking at a "mtb-lite tire", and not an "all-road" tire, so much. Call this thing a "monster-cross"tire then. Maybe that is what it is. Well, at any rate, the Ravager seems to fall into the end of the spectrum that is more dirt/single track and less "road". I just thought it was an interesting tire from that standpoint.

The whole adventure bike thing, as described by the industry now, is another post for another day. Short version: They are missing the boat big time as far as bringing back riders and bringing in new ones because of how they are portraying these niche bikes now.

One of the several connections I have with Brian and Alexa
Special Occasion:

Today is a special day for a couple that have special connections with myself. Yes......a bicycle is part of the story, so hold on here.

I normally don't get off topic here too far, but today is a special occasion since a former co-worker of mine is marrying a women I've known since she was born. Literally since she was born. I used to be very close to her family, and since I know both of the folks in this marriage, and one of them bequeathed the Surly 1X1 to me , I wanted to give a G-Ted Productions "Congratulations" to the couple.

So, I am attending the nuptials and will be off gallivanting around Central Iowa all weekend long. I won't be getting any bicycling done, but that's excusable for this deal, in my opinion. I wouldn't miss this and since it is happening so close, I don't have to. I am not sure I'll have much else going on except maybe keeping tabs on cards coming in for Trans Iowa, so don't look for any adventurous posts come Monday!

Okay, that's a wrap. Forget about football and get outside and ride, y'all!!

 

Thursday, October 06, 2016

Back On It

Fresh blue skies and lots of wind.
The Fat Bike Century kind of knocked me for a doozy this week so far until Wednesday when I finally felt "okay". I didn't want to get out of bed Wednesday morning, and I was still kind of in a funk till about noon, but it passed and I finally felt like I could maybe take a nice, easy ride out in the country.

Monday my legs were still toasted, Tuesday I felt better, but both days I was fatigued and by evening time I was falling out of my chair. Of course, I was still commuting by bicycle. The Big Dummy may have been a bit much, but ya gotta do what ya gotta do! That's my transportation to work and back for the time being.

At any rate, the plan yesterday was to just do a nice, easy ride out on the gravel, nothing too crazy. I took out the Black Mountain Cycles "Orange Crush" rig because it has these Arisun tires on it that I am testing out. I like that bike a lot anyway, so that was okay by me. The trouble is that my left shoulder isn't digging the traditionally shaped drops or even the slightly flared Cowbells, like the Orange Crush has on it now. That dang injury from last Winter hangs on, but it seems to get better bit by bit. It is just taking a very long time to come around. So, maybe I need to think about different bars on that bike and on  a few others. We'll see........

In the meantime, I wasn't planning on some multi-hour, all day ride, so the Cowbells should be fine, but I would see about that later. The Fat Bike Century actually did put the hurt on that shoulder, (despite it having flat bars), so I wasn't sure how this was going to go. Otherwise it was a splendid day, with maybe a stiff wind, but otherwise perfect. Wind isn't that big of a deal anymore since I have that almost every ride anyway. It has just become part of the whole experience. The wind has to get pretty bad for me to start complaining about it now.

Petrie Road looking East.
The Sun was out, and the roads were in great shape at first. Not too much gravel, and with the rain we had overnight, not too dusty either. I was feeling pretty good, actually. The legs had a bit of snap in them after all. So, the "easy" ride started turning into......something a bit more than that. I ended up dialing it back a bit, but it felt good to be able to go fast, even if just for a bit. I think it was that fat bike and riding it 100 miles. The Orange Crush was lighter, easier to move with skinnier tires. It was almost like when my friend Ari rides his road bike and he refers to it as his "cheater bike". Because it is easier. Yeah......it was easier!


Giving my "cheater bike", and myself, a quick break.
I ended the ride after about 20 or so miles, which I figured was a good reintroduction to gravel after the Fat Bike Century ride. I didn't want to over do it and get really tired afterward or worse, sick. I think that felt about right anyway. The ride was pleasant, despite the wind, and it was a great day to be outside. I was really glad I got out there and back on it again.

Now my next, and last scheduled ride for the year, is coming up at the end of this month. I want to be ready for that, so I am going to work on getting some good rides in before then. Hopefully the weather holds up for that ride. Hint: I will be using my Gen I Fargo for this particular ride. 

Besides that, I want to sneak in some bigger rides before the year is out. I have to finagle a way to finish up my Cup-O-Dirt challenge and my last scheduled ride could be part of that. Otherwise I have to knock out three really big rides in less than three months and who knows what the weather will be like coming up in November and December. It seems weird to be thinking about those months, and yet here we are. The end of the 2016 calendar is coming fast.

The fields are being emptied, the leaves are changing quickly, and my cycling mode is going to be switching to the Winter selection soon. My fat bikes are ready, that's for sure. But until that time comes I will be riding my gravel rigs and maybe the odd single speed mtb rig throughout the Fall season. I have to do at least one fall mtb ride!


Back On It

Fresh blue skies and lots of wind.
The Fat Bike Century kind of knocked me for a doozy this week so far until Wednesday when I finally felt "okay". I didn't want to get out of bed Wednesday morning, and I was still kind of in a funk till about noon, but it passed and I finally felt like I could maybe take a nice, easy ride out in the country.

Monday my legs were still toasted, Tuesday I felt better, but both days I was fatigued and by evening time I was falling out of my chair. Of course, I was still commuting by bicycle. The Big Dummy may have been a bit much, but ya gotta do what ya gotta do! That's my transportation to work and back for the time being.

At any rate, the plan yesterday was to just do a nice, easy ride out on the gravel, nothing too crazy. I took out the Black Mountain Cycles "Orange Crush" rig because it has these Arisun tires on it that I am testing out. I like that bike a lot anyway, so that was okay by me. The trouble is that my left shoulder isn't digging the traditionally shaped drops or even the slightly flared Cowbells, like the Orange Crush has on it now. That dang injury from last Winter hangs on, but it seems to get better bit by bit. It is just taking a very long time to come around. So, maybe I need to think about different bars on that bike and on  a few others. We'll see........

In the meantime, I wasn't planning on some multi-hour, all day ride, so the Cowbells should be fine, but I would see about that later. The Fat Bike Century actually did put the hurt on that shoulder, (despite it having flat bars), so I wasn't sure how this was going to go. Otherwise it was a splendid day, with maybe a stiff wind, but otherwise perfect. Wind isn't that big of a deal anymore since I have that almost every ride anyway. It has just become part of the whole experience. The wind has to get pretty bad for me to start complaining about it now.

Petrie Road looking East.
The Sun was out, and the roads were in great shape at first. Not too much gravel, and with the rain we had overnight, not too dusty either. I was feeling pretty good, actually. The legs had a bit of snap in them after all. So, the "easy" ride started turning into......something a bit more than that. I ended up dialing it back a bit, but it felt good to be able to go fast, even if just for a bit. I think it was that fat bike and riding it 100 miles. The Orange Crush was lighter, easier to move with skinnier tires. It was almost like when my friend Ari rides his road bike and he refers to it as his "cheater bike". Because it is easier. Yeah......it was easier!


Giving my "cheater bike", and myself, a quick break.
I ended the ride after about 20 or so miles, which I figured was a good reintroduction to gravel after the Fat Bike Century ride. I didn't want to over do it and get really tired afterward or worse, sick. I think that felt about right anyway. The ride was pleasant, despite the wind, and it was a great day to be outside. I was really glad I got out there and back on it again.

Now my next, and last scheduled ride for the year, is coming up at the end of this month. I want to be ready for that, so I am going to work on getting some good rides in before then. Hopefully the weather holds up for that ride. Hint: I will be using my Gen I Fargo for this particular ride. 

Besides that, I want to sneak in some bigger rides before the year is out. I have to finagle a way to finish up my Cup-O-Dirt challenge and my last scheduled ride could be part of that. Otherwise I have to knock out three really big rides in less than three months and who knows what the weather will be like coming up in November and December. It seems weird to be thinking about those months, and yet here we are. The end of the 2016 calendar is coming fast.

The fields are being emptied, the leaves are changing quickly, and my cycling mode is going to be switching to the Winter selection soon. My fat bikes are ready, that's for sure. But until that time comes I will be riding my gravel rigs and maybe the odd single speed mtb rig throughout the Fall season. I have to do at least one fall mtb ride!


Wednesday, October 05, 2016

Trans Iowa v13: Registration Update

Okay- I figured since the registration is underway for T.I.v13 I would give a bit of an update on how all of that is going so far.

What I will not do is go over "how you register" because that ship has sailed. You either were paying attention or you are not. I also am not answering any e-mails about that, and I did get one, by the way. Like I said, you either were paying attention or you weren't.

So, anyway, yeah....... eight of the "Plus Six" and Winners have taken spots which could add up to 25 total. The way it is going, I don't think that is going to happen. The window for that category closes this weekend. We'll see if I get any last minute takers. I suppose there may be a few, but usually these come on the front end and then they peter out in terms of numbers. I am thinking I'll have about 10-14 spots to add to the 55 total for the Veteran's Lottery draw.

The Veteran's registration started this week, and so far I have one card that has made it here, but that window doesn't close for over a week, and I am thinking a bunch of cards are going to show up in the next three days and beyond. I am scanning them over for the proper required information and if they pass, I will post them on a separate page which can be found on the Trans Iowa site called "Veteran's Lottery Page". All cards that will end up in the lottery for the Vets will get the names listed there so you'll be able to see if your card made it in or not. NOTE: If your card gets sent in, and your name doesn't show up, well- you got something wrong. I'm not going to spend the time to tell you what that is. Could you send another card? Yeah.......I suppose you could try that, but why not get it right the first time? Usually folks screw up on penmanship, but sometimes they get other things completely screwed up too. Usually it is penmanship. So, do what you have to do to make it readable folks. It isn't that hard. 

When the Rookie thing happens I'll do a similar page for that.  

Now on to other stuff like the course! I have been working on the course for a long time and now the time is coming up that I will be actually going out to check on it all. That will happen October 15th. That will be a long stinkin' day in the "Truck With No Name", and there will be a report afterward. I have gotten some secret spy reports on some of the roads already from my agents in the field, so I hope to make the recon in a day. We will see......

Trans Iowa v13: Registration Update

Okay- I figured since the registration is underway for T.I.v13 I would give a bit of an update on how all of that is going so far.

What I will not do is go over "how you register" because that ship has sailed. You either were paying attention or you are not. I also am not answering any e-mails about that, and I did get one, by the way. Like I said, you either were paying attention or you weren't.

So, anyway, yeah....... eight of the "Plus Six" and Winners have taken spots which could add up to 25 total. The way it is going, I don't think that is going to happen. The window for that category closes this weekend. We'll see if I get any last minute takers. I suppose there may be a few, but usually these come on the front end and then they peter out in terms of numbers. I am thinking I'll have about 10-14 spots to add to the 55 total for the Veteran's Lottery draw.

The Veteran's registration started this week, and so far I have one card that has made it here, but that window doesn't close for over a week, and I am thinking a bunch of cards are going to show up in the next three days and beyond. I am scanning them over for the proper required information and if they pass, I will post them on a separate page which can be found on the Trans Iowa site called "Veteran's Lottery Page". All cards that will end up in the lottery for the Vets will get the names listed there so you'll be able to see if your card made it in or not. NOTE: If your card gets sent in, and your name doesn't show up, well- you got something wrong. I'm not going to spend the time to tell you what that is. Could you send another card? Yeah.......I suppose you could try that, but why not get it right the first time? Usually folks screw up on penmanship, but sometimes they get other things completely screwed up too. Usually it is penmanship. So, do what you have to do to make it readable folks. It isn't that hard. 

When the Rookie thing happens I'll do a similar page for that.  

Now on to other stuff like the course! I have been working on the course for a long time and now the time is coming up that I will be actually going out to check on it all. That will happen October 15th. That will be a long stinkin' day in the "Truck With No Name", and there will be a report afterward. I have gotten some secret spy reports on some of the roads already from my agents in the field, so I hope to make the recon in a day. We will see......

Tuesday, October 04, 2016

WW4M: Big Dummy

Big Dummy- finally.
This is another "WW4M" post. That means "What Works For Me" and it may not work for you. So, take that with the following words into consideration.....

Cargo carrying is something that makes your cycling life even more fun and versatile. Big Dummy owners already get this, but if you've never been able to figure out the "why" of some rigs like the Big Dummy, then maybe this post will help out with that. The simple thing to keep in mind though is carrying stuff. Essentially, that's what the Big Dummy is all about.

So, have you ever ridden your bicycle down to the convenience store, bought a sixer, or a gallon of milk, or maybe a bag of chips and a frozen pizza, and tried riding home with any of those things dangling from a plastic sack from your handle bars? It isn't fun, and it is potentially dangerous. Now think about buying all that stuff I mentioned and getting it home. Yeah....... Not happening, so you drive your car. What a hassle! If you had a Big Dummy, you could ride your bike there, go past the park, check out the flowers in the neighborhood, and buy a lemonade from those kids on the corner you always fly past when you are in your car. That's what a Big Dummy is for, ya big dummy! 

Okay, enough about your sedentary lifestyle, (only partially kidding), and on with the traits of this long tailed hauler that are unique. First off, the long back end...... Yeah, about that. You aren't going to be popping wheelies on this rig, (although somewhere I've seen it done), but with a bit of finesse and care, you can pop up that front wheel over curbs and smaller obstacles. I like my big, poofy 2.4" Bontrager XR-1 on the Northpaw rims which make it possible for me to run about 22psi and get a little cush when I do pop up over a curb. That's using the "YesTubes" method, by the way. I haven't gone tubeless yet. 

A key to making this work- The Paul Components Tall & Handsome seat post.
 I've spoken to a few other Big Dummy owners and they seem to agree with me that the Big Dummy has a short reach. or in old mtb jargon- a short top tube. This seems to call out for a set back seat post, or maybe even sizing up on the frame. I have a Large and I am sure I could have gone with an XL, since these have copious stand over height. 

Well, I ended up with a Large and I also decided to use a Brooks B-17 I had. Double whammy bad deal there for getting your set back on the saddle right. So, my answer came in the form of the excellently made, but very spendy Paul Components Tall & Handsome seat post.  It gets that Brooks where it belongs and it is a really nice seat post. Even the black anodization seems somehow richer than ordinary posts you see every where. Well, that's hard to portray in words, so you'll just have to take my word for that. 

So there's that short cockpit deal, but other than this the Big Dummy is really not too hard to handle. It steers a bit oddly, but nothing like a tandem does. You can get used to that steering deal easily. It rides really well. In fact, it goes right along much better than you'd expect, and the more stuff you throw in the back, the better it gets. In fact, I wouldn't be at all surprised to learn that Surly's wizards of doom made it so that the Big Dummy is best when burdened. 

Put on some big tires and rims for the best Big Dummy action.
 So, yeah.... For me it all comes down to carrying stuff, like I said earlier. I love figuring out what I can do with this bike. For instance, I commuted for years with a messenger bag. It was cool, and I could carry a lot, but I was always fussing with that thing, and a lot of the time it was in the way, or uncomfortable. Now I just toss that stuff into the "cargo bay" of the Big Dummy and ride bare backed and free. Plus, I don't have to worry about "maxing out" my carrying capacity because, well, the Big Dummy can do waaaay more than what I would normally consider. 

Examples: I went up the other day and grabbed a ten pound bag of charcoal for grilling while also carrying my pump and two tubes in boxes along with a cable lock and a jacket, ya know.....just in case. Or how about just yesterday. I took so much packing material home to send out a frame I sold that the bundles were about the size of four bed pillows and I had all that tube and pump stuff in there along with a jacket, ya know......just in case. Try stuffing all of that in your messenger bag or back pack! Not happening folks. That's why something like a Big Dummy is super cool. 

I have more projects lined up for this rig. I'm going to add my XtraCycle Wideloaders, which are tubular and fabric "shelves" that stick out on each side of a Big Dummy frame. Then I'm going to haul some stuff for a house project, and take cardboard to the recycler, plus take bottles and cans back to the store, and more. Just finding excuses to use a Big Dummy is fun for me, anyway. Maybe you think it is, well.......just dumb! Whatever. I am having a good time with this thing, and I think more people should be on bicycles like this. 

Look for more about this bike in the future. 

Disclaimer: I bought this Big Dummy with my own damn money and I was not paid nor bribed for this post. So there. 

WW4M: Big Dummy

Big Dummy- finally.
This is another "WW4M" post. That means "What Works For Me" and it may not work for you. So, take that with the following words into consideration.....

Cargo carrying is something that makes your cycling life even more fun and versatile. Big Dummy owners already get this, but if you've never been able to figure out the "why" of some rigs like the Big Dummy, then maybe this post will help out with that. The simple thing to keep in mind though is carrying stuff. Essentially, that's what the Big Dummy is all about.

So, have you ever ridden your bicycle down to the convenience store, bought a sixer, or a gallon of milk, or maybe a bag of chips and a frozen pizza, and tried riding home with any of those things dangling from a plastic sack from your handle bars? It isn't fun, and it is potentially dangerous. Now think about buying all that stuff I mentioned and getting it home. Yeah....... Not happening, so you drive your car. What a hassle! If you had a Big Dummy, you could ride your bike there, go past the park, check out the flowers in the neighborhood, and buy a lemonade from those kids on the corner you always fly past when you are in your car. That's what a Big Dummy is for, ya big dummy! 

Okay, enough about your sedentary lifestyle, (only partially kidding), and on with the traits of this long tailed hauler that are unique. First off, the long back end...... Yeah, about that. You aren't going to be popping wheelies on this rig, (although somewhere I've seen it done), but with a bit of finesse and care, you can pop up that front wheel over curbs and smaller obstacles. I like my big, poofy 2.4" Bontrager XR-1 on the Northpaw rims which make it possible for me to run about 22psi and get a little cush when I do pop up over a curb. That's using the "YesTubes" method, by the way. I haven't gone tubeless yet. 

A key to making this work- The Paul Components Tall & Handsome seat post.
 I've spoken to a few other Big Dummy owners and they seem to agree with me that the Big Dummy has a short reach. or in old mtb jargon- a short top tube. This seems to call out for a set back seat post, or maybe even sizing up on the frame. I have a Large and I am sure I could have gone with an XL, since these have copious stand over height. 

Well, I ended up with a Large and I also decided to use a Brooks B-17 I had. Double whammy bad deal there for getting your set back on the saddle right. So, my answer came in the form of the excellently made, but very spendy Paul Components Tall & Handsome seat post.  It gets that Brooks where it belongs and it is a really nice seat post. Even the black anodization seems somehow richer than ordinary posts you see every where. Well, that's hard to portray in words, so you'll just have to take my word for that. 

So there's that short cockpit deal, but other than this the Big Dummy is really not too hard to handle. It steers a bit oddly, but nothing like a tandem does. You can get used to that steering deal easily. It rides really well. In fact, it goes right along much better than you'd expect, and the more stuff you throw in the back, the better it gets. In fact, I wouldn't be at all surprised to learn that Surly's wizards of doom made it so that the Big Dummy is best when burdened. 

Put on some big tires and rims for the best Big Dummy action.
 So, yeah.... For me it all comes down to carrying stuff, like I said earlier. I love figuring out what I can do with this bike. For instance, I commuted for years with a messenger bag. It was cool, and I could carry a lot, but I was always fussing with that thing, and a lot of the time it was in the way, or uncomfortable. Now I just toss that stuff into the "cargo bay" of the Big Dummy and ride bare backed and free. Plus, I don't have to worry about "maxing out" my carrying capacity because, well, the Big Dummy can do waaaay more than what I would normally consider. 

Examples: I went up the other day and grabbed a ten pound bag of charcoal for grilling while also carrying my pump and two tubes in boxes along with a cable lock and a jacket, ya know.....just in case. Or how about just yesterday. I took so much packing material home to send out a frame I sold that the bundles were about the size of four bed pillows and I had all that tube and pump stuff in there along with a jacket, ya know......just in case. Try stuffing all of that in your messenger bag or back pack! Not happening folks. That's why something like a Big Dummy is super cool. 

I have more projects lined up for this rig. I'm going to add my XtraCycle Wideloaders, which are tubular and fabric "shelves" that stick out on each side of a Big Dummy frame. Then I'm going to haul some stuff for a house project, and take cardboard to the recycler, plus take bottles and cans back to the store, and more. Just finding excuses to use a Big Dummy is fun for me, anyway. Maybe you think it is, well.......just dumb! Whatever. I am having a good time with this thing, and I think more people should be on bicycles like this. 

Look for more about this bike in the future. 

Disclaimer: I bought this Big Dummy with my own damn money and I was not paid nor bribed for this post. So there.